I was getting ready to pull a project out of the vacuum press and I decided this would be the perfect time to shoot a test video for my new audio equipment. Besides that, popping the vacuum press open is one of my favorite moments in the shop - and now you get to share in it!
In this video, I do not get specifically into the step-by-step of bent lamination and using the vacuum press, but it is highly informative. You will get to see the actual moment a project is pulled out of the vacuum press and the information I share is good context based, working knowledge for bent lamination procedure and product.
This video shows a good example of how a vacuum press might be used. The vacuum press is a great tool to have in the shop. It has opened many doors for me since it allows for easy clamping of projects in a way that standard clamps cannot. The vacuum press really made veneer work a much more simple and lower risk procedure in my shop.
Links
VacuPress MachineNo doubt you will be asking for the following links so here they are for your further research!
Vacuum Press Machines (I did not see exactly my model, it is a few years old but there are some similar.)
I have been pretty anxious to get out more video, especially after all the effort I have invested in the infrastructure for creating better videos.
Well things did not go smooth for this video. I started out by setting a record for the number of takes to get a clean 1st scene. I don't know why my mind really kept dropping off. (I have a lot of crap rattling around up there.)
The next thing to happen was that after I got rolling on the video recording, I quit checking the playbacks very often because I felt comfortable everything was going OK. I have had an especially difficult time dialing in my audio, but after playing back a handful of shots I felt confident everything was recording good.
Boy, was I wrong. I knew that I was not dealing with a quality wireless mic system and that this was actually part of the problem. Well, that system really puked out on me altogether while recording.
Making Lemonade From Lemons
This was extremely disappointing, shooting video is very time intensive and this all equals wasted time. I was left with only 2 good scenes, but only 1 that had a good piece of woodworking advice. The other scene merely shared the application for my bent lamination to create context.
Other than that I just had the numerous outtake shots. OK, I figured, let's just make some lemonade out of lemons and so I put this video together.
So the video is basically a blooper reel but part of the good shot is at the end that has a real solid piece of woodworking advice. It is a principle that I exercise in my own shop.
I call the video "Crap to Gold Nuggets" and you will see why.
I have a new wireless system ordered & on the way. Hope you enjoy!
It's been a lot of work to get to this point. Since taking a beating from the recession, I took all of the work I could get to recover over the last couple of years. Between working projects out of my shop, working with another contractor, and Rita opening a cafe in downtown Billings, there was not any free time to get out any blogs let alone video.
I have been chomping at the bit to get back to sharing with the woodworking community. Sharing the craft with others has become a passion of mine. I have enjoyed an amazing journey in my own growth of woodworking skills, and I love helping others so that they may enjoy that same growth as well. I also find that sharing has sparked a new level of growth in myself. The woodworking journey never ends!
A Peak Behind The Scenes
Another task that took up my time, was setting up the infrastructure for better video. I recognized that I needed to make some changes in the shop to produce higher quality video. This included adding more light fixtures to increase lumens per square foot and to create even lighting. I went from 44 bulbs to 84. Yes, I nearly doubled my light output (and power consumption.)
Video Lighting Mode
Video Lighting Mode 2
I set the wiring and switches up for "work mode" and "video mode." In work mode I only run the same lights that I always have to provide enough light for working on projects. In video mode I turn on the additional lighting to provide brighter, more even coverage for a better video image.
Replacing Magnetic Ballast I noticed another problem during some test shoots, the old magnetic ballasts created a lot of hum and buzz. So I changed out the last 10 magnetic ballasts for new electronic units. Not only do the lights run silently now, but the start up is much faster. This was a nice improvement.
It is a good thing to have remodeling skills. I have saved myself a good chunk of change being able to do the work myself but it has been a lot of time and effort.
Third Time Is A Charm
Removing Attic LadderThe new lights required a good bit of wiring, and the fixture layout required moving the attic access ladder to a new location. Removing & re-installing the spring loaded attic ladder by myself is something like handling a human size mouse trap. The effort was worthwhile since I found a better location that does not require me to move anything on the floor to drop the ladder. Previously, I had to move my 8" jointer to drop the attic ladder. My shop layout is on plan #3 and so these things happen. I think that I have finally nailed it down this time both on the floor and ceiling layout.
(Clicking on the thumbnails will open larger image.)
I'm A Mac
Other infrastructure upgrades include a new 27" iMac (freaking sweet!) and editing software. I upgraded from iMovie, which I think is a great program, to Final Cut Pro X. FCPX is waaay more powerful and with that power comes a new level of complexity.
Just like with woodworking, you can read or watch tutorials on the subject all you want, but it's only by doing will you really understand the craft. I was going to do a shop tour, but it turned into a simple look around the shop with a movie preview theme for fun. It's short but it was an exercise for me to try out the new capabilities of FCPX.
Stay tuned, there will be more videos coming from the American Craftsman Workshop as I continue supporting the woodworking community!
Your friend in the shop,
Todd A. Clippinger
Share the Love~Share the Knowledge
American Craftsman Workshop
The goal of the American Craftsman Workshop is to provide education, encouragement, and inspiration to aspiring woodworkers and DIY'ers.
VacuPress MachineNo doubt you will be asking for the following links so here they are for your further research!
